Launch Tech USA Radar 3 in 1 (ACC + Doppler + Corner Reflector) Set with Bags

Description

Launch Tech USA Radar 3 in 1 (ACC + Doppler + Corner Reflector) Set with Bags

Part number 701070015, the Launch Tech Radar 3-in-1 is a single calibration stand engineered to support three distinct radar target types: a forward-facing ACC radar reflector for adaptive cruise control sensors, a Doppler simulator for OEM procedures that demand a moving-object signal, and a corner reflector dedicated to blind spot monitoring (BSM) and rear cross-traffic alert (RCTA) sensors. Rather than purchasing, maintaining, and storing three separate calibration rigs, your shop operates from one compact stand with interchangeable targets ÔÇö packaged with a travel case suited equally for in-shop and mobile use.

Priced at $4,399.99, the Radar 3-in-1 comes in well under the X-431 ADAS PRO PLUS and ADAS Mobile Plus platforms, which run $9,995ÔÇô$14,495. For a collision center or independent repair shop that needs to handle radar calibration without committing to a full dedicated ADAS bay, this is the right entry point.

Who Needs This Unit

Any shop performing the work below will encounter radar calibration requirements ÔÇö and this stand addresses the three target types you will see most often:

• Front-end and bumper repairs ÔÇö Removal or replacement of the bumper or bumper cover triggers a mandatory alignment verification and recalibration of the forward-facing radar sensor.
• Radar sensor R&R ÔÇö Installing or repositioning a radar module requires a post-installation static calibration before the vehicle is released to the customer.
• Collision repairs affecting sensor mounting ÔÇö Frame or structural repairs in the vicinity of radar sensor locations can shift sensor aim, invalidating any previous calibration on record.
• Suspension and alignment work ÔÇö Certain OEMs mandate radar recalibration following alignment corrections that exceed specified tolerances.
• BSM and RCTA sensor service ÔÇö The corner reflector target addresses rear-corner radar sensors used in blind spot and cross-traffic alert systems, which operate independently from the front-facing ACC radar.

What the Three Targets Do

• ACC Radar Target (LAM05-02) ÔÇö A static reflector plate used for forward radar calibration procedures. The vehicle is placed at a precise distance from the target on level ground, and the connected Launch diagnostic tool walks through the calibration sequence. This is the highest-frequency target in the set, covering adaptive cruise control and autonomous emergency braking systems.
• Doppler Simulator (LAC05-04) ÔÇö Certain OEM radar calibration routines require detection of a simulated moving object rather than a stationary reflector. The Doppler simulator generates that signal, enabling your technicians to complete procedures that a static target cannot support on its own.
• Corner Reflector ÔÇö Positioned at the rear corners of the vehicle to service BSM and RCTA radar sensors. These sensors are distinct from the front ACC radar and require a dedicated calibration target and their own procedure sequence.

Stand Features

• Single-button height adjustment ÔÇö Target height is set without tools, allowing quick transitions between target configurations and different vehicle types.
• Interchangeable targets ÔÇö All three calibration targets attach to the same stand frame. No additional tripods or separate support structures are required.
• Lightweight and portable ÔÇö The stand is built to move freely across the shop floor or travel with technicians on mobile service calls.
• Travel and storage cases included ÔÇö Protective bags for the stand and all accessories ship with the full set, keeping components organized and protected in transit.

What Is in the Box

• 3-IN-1 Main Unit
• ACC Radar Target (LAM05-02)
• Doppler Simulator (LAC05-04)
• Corner Reflector
• Mounting Adapter for ACC Radar Target
• 3.5mm Single Hex (6PT) Socket Tool
• Five-line Laser Device (LAM09-01)
• Power Adapter
• Plumb Line (LAM09-06)
• Laser Reflector (LAM09-03)
• Auxiliary Mirror (LAM09-04)
• Tape Measure
• Positioning Bracket (LAM09-05)
• Cross Stickers (10)
• Travel/Storage Case with Bags
• User Manual
• Activation PIN Card

Compatible Launch Diagnostic Tools

• Professional diagnostic platforms: Throttle V, Torque Link, Turbo III
• ADAS systems: X-431 ADAS PRO PLUS, X-431 ADAS MOBILE PLUS, X-431 ADAS HD, RADAR 3-IN-1

The Radar 3-in-1 is built to operate within the Launch ADAS calibration workflow ÔÇö the diagnostic platform drives the procedure, and this stand delivers the physical targets the software calls for at each step. Vehicle coverage is determined by the connected diagnostic tool. Reach out to ADAS Calibration Tools with any compatibility questions regarding specific makes, models, or OEM radar systems.

Where This Fits in the Launch ADAS Lineup

• Radar 3-in-1 ÔÇö $4,399.99 (our price, vs. $4,495.95 MSRP) ÔÇö This unit. Three radar targets, one stand. The right solution for shops focused on radar-specific calibration who don’t need a full camera and sensor suite.
• X-431 ADAS HD ÔÇö $9,995.00 ÔÇö A complete ADAS calibration system covering cameras, radar, and additional sensor categories. Suited for shops with higher ADAS volume or a wider range of OEM requirements.
• X-431 ADAS Mobile Plus ÔÇö $9,995.99ÔÇô$14,495.99 ÔÇö A mobile ADAS calibration configuration designed for operations running mobile ADAS service or requiring flexible deployment across multiple locations.
• X-431 ADAS PRO PLUS ÔÇö Contact us for current pricing. Expanded target coverage for high-volume ADAS shops with broad OEM demands.

When the Radar 3-in-1 Is the Right Call

This stand is purpose-built for collision shops and independent repair facilities already handling radar R&R and bumper work that need a dependable, portable target set without the overhead of a dedicated ADAS bay. If your diagnostic platform is a Launch Throttle V, Torque Link, Turbo III, or any X-431 ADAS system, the Radar 3-in-1 slots directly into that existing workflow.

If your shop also calibrates cameras, lidar, or a broader array of ADAS sensors, the X-431 ADAS HD or ADAS Mobile Plus may be the stronger fit. ADAS Calibration Tools can walk through the comparison based on your OEM mix and monthly service volume.

Why Buy From ADAS Calibration Tools?

• ADAS specialist ÔÇö we know the Launch lineup end-to-end and can identify exactly which configuration matches your shop’s workflow and volume.
• Free shipping on this unit to the lower 48 states.
• Free tech support ÔÇö call us at 800-123-4567 and speak with someone who has hands-on experience with this equipment.
• Full manufacturer warranty ÔÇö we manage warranty claims directly, so you’re not navigating that process alone if an issue arises.
• Straightforward upgrade guidance ÔÇö if the Radar 3-in-1 isn’t the right match for your shop’s volume or OEM mix, we’ll tell you honestly and point you to the configuration that is.

Call 800-123-4567 for quick answers and help!