AVM Target and Bracket fro Toyota

Description

Autel AVM Target and Bracket for Toyota (CSC0804-03)

The Autel CSC0804-03 is the OEM-specified Around View Monitor (AVM) target and bracket assembly for Toyota vehicles, built specifically for use within the Autel ADAS calibration ecosystem. For shops performing bumper work, camera R&R, or suspension repairs on Toyota trucks, SUVs, and sedans, this is the target assembly required to bring the surround-view system back to factory calibration before the vehicle leaves your bay.

AVM systems combine feeds from four cameras ÔÇö front, rear, and both side mirrors ÔÇö into a seamless bird’s-eye composite image. Whenever one of those cameras is disturbed, the stitch lines shift and the composite image falls out of alignment. Each camera must be re-aimed to factory specification using the correct target pattern placed at the correct position. Substituting the wrong target or a generic alternative may produce a calibration result that shows a pass on the scan tool screen while leaving the system misaligned under real driving conditions.

What This Target Does

• Toyota-specific AVM pattern: The target pattern matches exactly what Toyota’s AVM calibration routine is designed to read. Autel’s diagnostic software keys on specific visual markers ÔÇö use the wrong pattern and the routine will either throw an error or, more dangerously, complete with corrupt data.
• Rigid bracket mount: The bracket sets the target at the vehicle-specific height and angle required by Autel’s CSC frame setup guide for Toyota applications. Bracket rigidity is critical ÔÇö any flex or unintended tilt introduces measurable error into the final calibration output.
• CSC frame compatible: Mounts directly onto the Autel Calibration Standard Component (CSC) frame. Shops already running the MaxiSYS ADAS system with a CSC frame can integrate this target without sourcing any additional hardware.
• Pairs with MaxiSYS software: Compatible with MaxiSYS Ultra, MS909, MS919, and Elite II tablets running Autel ADAS software. The software walks the technician through target positioning, verifies placement, and runs the camera re-learn sequence.

When Does a Shop Need This?

• Bumper replacement or repair: Rear and side AVM cameras are mounted in or near bumper fascias and mirror housings. R&R of any of those panels requires AVM recalibration before delivery.
• Mirror housing replacement: Side-view cameras on Toyota models are integrated directly into the mirror housing. Swapping a mirror housing ÔÇö even when the camera unit itself is not replaced ÔÇö typically triggers a recalibration requirement.
• Collision repair: Frame pulls, suspension realignment, and any procedure that alters the vehicle’s geometry relative to camera mounting points will necessitate recalibration.
• Camera replacement: Any direct swap of an AVM camera unit requires the full calibration procedure with this target.
• Post-alignment checks: Certain Toyota models flag AVM recalibration after significant alignment corrections have been performed.

Toyota Coverage

This target supports Toyota models covered under Autel’s AVM calibration procedures. Specific model-year and trim-level coverage is determined by your active MaxiSYS software subscription. Contact ADAS Calibration Tools at 800-123-4567 to verify coverage for a particular Toyota model before placing your order.

What’s in the Box

• AVM calibration target panel (Toyota-specific pattern)
• Mounting bracket for CSC frame
• Mounting hardware

Note: The CSC calibration frame is sold separately. This target is a component accessory intended for shops already equipped with the Autel ADAS CSC frame system.

Configuration Fit

• Right for your shop if: You’re already running Autel ADAS with a CSC frame and need to expand your calibration menu to include Toyota AVM procedures.
• Not what you need if: You don’t yet have a CSC frame ÔÇö begin with the MaxiSYS ADAS complete kit and add vehicle-specific targets such as this one once your core system is in place.

Why Buy From ADAS Calibration Tools?

• Specialist: ADAS Calibration Tools focuses exclusively on professional diagnostic and ADAS calibration equipment. Our team understands the Autel ecosystem at a depth that general distributors don’t match.
• Free shipping: Available on all orders shipping within the contiguous U.S.
• Free tech support: Reach us at 800-123-4567 and speak with someone who works in ADAS calibration daily ÔÇö not a general-purpose call center.
• Full manufacturer warranty: Every Autel product we sell carries the full OEM warranty, and we manage warranty matters directly on your behalf.
• Straight answers: If this target isn’t the right match for your current setup, we’ll point you toward what actually is.

Call 800-123-4567 for quick answers and expert guidance!